Robust DALI switching actuator for ceiling installation. Controllable via DALI bus, suitable for loads up to 2kW. Operates at -20°C to +60°C, IP20, with Wieland connectors.

wDALI Controls Wireless DALI Controls
overview
Wireless control of a DALI circuit
A wDALI control consists of at least two components: a receiving unit, which is connected to the DALI bus, and a control device (transmitter unit) that can be placed anyw

A remote control for DALI systems with 12 buttons. This remote control enables location independent control of a DALI system (light, blends, ventilators, … ). Each button can be individually configured with target address, button behaviour and DALI comman

The DALI USB is used as interface between the DALI Cockpit PC Software and the devices on the DALI bus. It enables the addressing and configuration of DALI installations. The DALI USB is available in 6 different versions: with strain relief, for DIN Rail

Compact sensor module with motion detection (PIR) and light intensity measurement for DALI and DALI-2 systems. The module can either be used to directly control the DALI system (application controller) or simply to gather measurements for a building manag

This interface converts DALI signals to a galvanically isolated, analogue 0-10V signal, thus enables the integration of operating devices with 1-10V control input into a DALI system. DALI Device Type 5 (IEC62386-206) compatible: linear or logarithmic dimm

Module with serial interface to communicate with the DALI bus via RS232, with RJ45 plug and screw terminals. Allows e.g. the connection of a PLC to a DALI system via RS232 for bidirectional data transmission. Suitable for addressing, configuration, status

DALI-2 ROT Touch
L3: Tunable White und Szenen

This interface converts DALI signals to an analogue 0-10V signal, thus enables the integration of operating devices with an electrically isolated 1-10V control input into a DALI system. DALI Device Type 5 (IEC62386-206) compatible: linear or logarithmic d

This compact 1HP DIN rail module enables the independent control of up to 4 DALI lines, which equals 256 DALI operating devices. Efficient scaling is possible with external DALI bus supplies. Via the DALI4Net connected control devices and control gear c

With the DALI Expander a new DALI sub-line can be created and supplied with power and information. The connected devices within the DALI sub-line can be controlled broadcast via the address of the DALI Expander. Alternatively the DALI sub-line can be cont

DALI PS serves as power supply for the DALI bus system. Voltage and current limitation according to standard as well as timing ensure a reliable bus communication. With the output current of up to 250mA an entire DALI line can be supplied. Up to 64 addres

DALI PS serves as power supply for the DALI bus system. Standardised voltage and current limitation as well as timing ensure a reliable bus communication. With the output current of up to 250mA and entire DALI line can be supplied. Up to 64 addressable DA

DALI LED-driver (CC) with 3 channels to control RGB luminaires via one DALI address (DT8). As alternative to the DT8 control the device also supports the operating modes Colour&Dim and SwitchDim2 (control via 2 switch inputs without DALI). Available with

Device with 2 DALI Tunable White LED dimmers. Suitable for constant voltage (CV) LED modules of 12V to 48V.

2 DALI addresses (Device Type 8, Color Type Tc), each DT8-Tc address allows independent control of brightness and color temperature.
Available

DALI Jalousie module can be used to control blind motors with 230V control input via DALI. Four configurable profiles can be programmed to open/close the blinds and to change the tilt angle. Different versions suitable for DIN rail mounting or remote ceil

With the DALI Temp PT1000 temperature can be measured. The measured temperature can be read using DALI scene values. Alongside the integrated temperature sensor, an external PT1000 sensing element can be added. The device can be used to control blinds or

This interface converts DALI signals to a 1-10V control signal, thus enables the integration of operating devices with 1-10V control input into a DALI system. With the help of the switching relay the power supply of operating devices can be switched on an

Interface with 4, from the DALI bus galvanically isolated, inputs for mains voltage. The inputs can be individually configured with target address, button behaviour and DALI commands. Beside the standard functions, dimming, switching, scene recall, etc.,

The DALI USB is used as interface between the DALI Cockpit PC Software and the devices on the DALI bus. It enables the addressing and configuration of DALI installations. The DALI USB is available in 6 different versions: with strain relief, for DIN Rail

DALI-2 ROT Integration
DALI-2 ROT Integration is a rotary and push button for integration into higher-level building management systems (WAGO, Beckhoff, LUNATONE DALI-2 KNX gateway).

increase the number of DALI lines for the DALI-2 Display 7”, 3 additional DALI lines, use in combination with a DALI-2 Display 7”


DALI-2 Display Bus Extension
The module is used in combination with a DALI-2 Display 7” Plus or DALI-2 Display 7” Emerg

DALI LED-driver (CV) with 3 independent channels. Each channel has its own DALI address. As alternative to the DT6 control the device also supports the operating modes Colour&Dim (suitable for RGB luminaires) and SwitchDim2 (control via 2 switch inputs wi

This interface converts DALI signals to a galvanically isolated PWM signal, thus enables the integration of operating devices with PWM control input into a DALI system. DALI Device Type 5 (IEC62386-206) compatible: linear or logarithmic dimming curve, 0-1