Phase dimmer with DALI input to control dimmable 230V luminaires in a DALI system. Available for leading edge, trailing edge or as universal device with automatic load detection. Available as compact 25W version or as 300W version. From Firmware 3.5 onwar

DALI LED-driver (CV) with 4 channels to control RGB or RGBW luminaires via one DALI address (DT8). As alternative to the DT8 control the device also supports the operating modes Colour&Dim and SwitchDim2 (control via 2 switch inputs without DALI). Availab

This compact module converts 0-10V input voltages into DALI light levels. Configurations can be made using the DALI Cockpit software. Target address and dimming characteristic can be configured.

The DALI-2 RM8 provide a relay contact that can be controlled via the DALI bus to switch continuous loads up to 2kW.

DALI-2 IoT Gateway is an interface to connect the DALI system with smart devices over the Internet of Things (IoT). With the DALI IoT Gateway, a simple realization of an intelligent system is possible, in which devices can be controlled and monitored with

Phase dimmer with DALI input to control dimmable 230V luminaires in a DALI system. Available for leading edge, trailing edge or as universal device with automatic load detection. Available as compact 25W version or as 300W version. From Firmware 3.5 onwar

The DALI USB is used as interface between the DALI Cockpit PC Software and the devices on the DALI bus. It enables the addressing and configuration of DALI installations. The DALI USB is available in 6 different versions: with strain relief, for DIN Rail

Module for the wireless connection of spatially separated DALI loads to a DALI system with BT5 Long Range. The transmitter sends DALI commands from the DALI system to one or more receivers. The receiver is available with or without an integrated DALI bus

Interface wirelessly connected to the DALI line. This battery powered wDALI module has four individually configurable switch inputs. The device can be mounted anywhere within the reception range of the receiver, which has to be connected to the DALI line.

DALI LED-driver. Input voltage 230VAC, output with secure isolation between mains and DALI. Output signal can be controlled via DALI or SwitchDim2.
Versions for constant current (250mA/350mA … 1050mA) and constant voltage (24V, 1A max.) are available.

DALI RM8/RM16 provides a via DALI bus controllable relay switch, which allows direct switching of permanent loads up to 2kW. Various compact designs and variations with make contact or changeover contact are available. The purposeful switching in voltage

Pushbutton coupler with 4 inputs to connect standard potential-free switches or pushbuttons. New functions, DALI-2 and NFC configuration!

DALI RM16 provides a via DALI bus controllable relay switch, which allows direct switching of permanent loads up to 2kW. Various compact designs and variations with make contact or changeover contact are available. The purposeful switching in voltage zero

DALI-2 CS, sensor module (motion/brightness), application controller and instance mode.
various versions available in this series

The DALI Room Controller serves as an interface between Bluetooth 5.0 and DALI.

The Lunatone smartphone application DALI-Cockpit Mobile offers a clear and simple interface with an installation assistant, various configuration options and a configurable

The capacitive 4” colour display with 24-bit colour depth allows both the configuration, as well as the control and operation of a DALI system. Numerous widgets enable customisation. Supported functions are dimming and switching of groups, recall of scene

The capacitive 7” colour display with 24-bit colour depth allows both the configuration, as well as the control and operation of a DALI system. Numerous widgets enable customisation. Supported functions are dimming and switching of groups, recall of scene

Compact sensor module with motion detection (PIR) and light intensity measurement for DALI and DALI-2 systems. The module can either be used to directly control the DALI system (application controller) or simply to gather measurements for a building manag

Compact sensor module with motion detection (PIR) and light intensity measurement for DALI-2 systems. The module gathers measurements for the building management system (instance mode) – (DALI-2 CS Master, WAGO, Beckhoff, etc.).

DALI LED-driver (CV) with 2 independent channels. Each channel has its own DALI address. As alternative to the DT6 control the device also supports the operating modes Balance&Dim, Dim2Warm (suitable for Tunable White luminaires) and SwitchDim2 (control v

The DALI Touchpanel is a multifunctional DALI control unit with up to 12 freely configurable keys. It is possible to choose between a selection of default user interfaces to control groups/scenes and colour/colour temperature. Each button can be individua

DALI PS serves as power supply for the DALI bus system. Standardised voltage and current limitation as well as timing ensure a reliable bus communication. With the output current of up to 250mA and entire DALI line can be supplied. Up to 64 addressable DA

DALI LED-driver (CV) with 3 channels to control RGB luminaires via one DALI address (DT8). As alternative to the DT8 control the device also supports the operating modes Colour&Dim and SwitchDim2 (control via 2 switch inputs without DALI). Available with

wDALI Controls Wireless DALI Controls
overview
Wireless control of a DALI circuit
A wDALI control consists of at least two components: a receiving unit, which is connected to the DALI bus, and a control device (transmitter unit) that can be placed anyw