Collection
DALI ROT is a rotary knob basis to control the light level of DALI luminaires. Versions for Tunable White or RGB-capable luminaires are also available. The device was developed to fit the rotary covers and knobs of most manufacturers and to enable their i
€88,06 Incl. tax
DALI LED-driver (CC) with 2 channels to control Tunable White luminaires via one DALI address (DT8). As alternative to the DT8 control the device also supports the operating modes Balance&Dim, Dim2Warm and SwitchDim2 (control via 2 switch inputs without D
€109,62 Incl. tax
This interface converts DALI signals into a 1-10V control signal and allows the integration of operating devices with two 1-10V control inputs for brightness and color temperature into a DALI system. Output mode for channel1 / channel2 can be defined as e
€150,96 Incl. tax
This interface converts DALI signals to a 1-10V control signal, thus enables the integration of operating devices with 1-10V control input into a DALI system. With the help of the switching relay the power supply of operating devices can be switched on an
€124,00 Incl. tax
This interface converts DALI signals to a galvanically isolated PWM signal, thus enables the integration of operating devices with PWM control input into a DALI system. DALI Device Type 5 (IEC62386-206) compatible: linear or logarithmic dimming curve, swi
€70,09 Incl. tax
DALI GC / GC-A is a control unit to address 2 DALI groups. With this compact module conventional light switches or pushbuttons can be used to send dimming and switching commands to 2 DALI groups. Using the dial on the back of the device the DALI/ luminari
€66,49 Incl. tax
Sensor Interface to connect conventional motion sensors or pushbuttons to a DALI system. Configuration options are for example: range, target address, DALI commands for on/off, hold time, … . Multiple sensors within one group synchronise automatically. Tw
€53,91 Incl. tax
Push button coupler with 4 inputs for connection with standard potential free switches or pushbuttons (max wire length 0.50m). Alternatively 0-10V signals or potentiometers can be connected. Each input can be individually configured with target address, b
€71,88 Incl. tax
The DALI CDC enables a day time based adjustment of colour temperature and light level for Tunable White capable DALI DT8 luminaires (circadian daylight curve). The curve can be adjusted to fit the respective application.
€237,22 Incl. tax
DALI Sequencer is a control unit to recall automatically timed instruction sequences. 4 different customised sequences can be programmed. Only one sequence can be active at a time, and is started and stopped by standard DALI commands. Housing variants fo
€248,00 Incl. tax
Module with serial interface to communicate with the DALI bus via RS232. Allows e.g. the connection of a PLC to a DALI system via RS232 for bidirectional data transmission. Suitable for addressing, configuration, status queries and monitoring. Housing var
€285,74 Incl. tax
DALI2 parts 101,102,207
Dimmable 12 V LED driver for constant voltage PWM-CV 75 W
Power 230VAC output 12V
€94,39 Incl. tax
DALI bus standard IEC62386-parts 101, 102, 207.
Output Voltage 10-24Vdc
Output Current Range350-700mA
Output Power Range 3,5W~12W
€38,88 Incl. tax
PWM-90-12DA2
AC-DC Single output LED driver Constant Voltage (CV); PWM output for LED strips; Output 12Vdc at 7.5A; Dimming with DALI; IP67
€48,28 Incl. tax
LCM-40DA2
AC-DC Multi-Stage LED driver Constant Current (CC); Modular output 0.35A/0.5A/0.6A/0.7A/0.9A/1.05A; Dimming with DALI 2.0 & push; extra 12Vdc at 50mA
€39,74 Incl. tax
LED driver (CV) with one channel, can be operated as PWMBooster or Dimmer. The device operates as PWM-Booster, if PWM-signals are applied to the input (50Hz-1kHz). If operated with 100kΩ potentiometer or 0-10V control devices (active and passive), the dev
€71,88 Incl. tax
This compact module converts analogue 0-10V control signals into DALI light levels. The module has an integrated bus supply for a small DALI system with up to 4 standard DALI ballasts (10mA). The device offers both a current sink and current source 0-10V
€73,68 Incl. tax
This compact module converts analogue 0-10V control signals into DALI light levels. The module has an integrated bus supply for a small DALI system with up to 4 standard DALI ballasts (10mA). The device offers both a current sink and current source 0-10V
€73,68 Incl. tax
Module with serial interface to communicate with the DALI bus via RS232. Allows e.g. the connection of a PLC to a DALI system via RS232 for bidirectional data transmission. Suitable for addressing, configuration, status queries and monitoring. Housing var
€285,74 Incl. tax