The DALI CDC enables a day time based adjustment of colour temperature and light level for Tunable White capable DALI DT8 luminaires (circadian daylight curve). The curve can be adjusted to fit the respective application.

Power Supply for DALI 4Net: PS 24V, 300mA

DALI-2 CS Integration THP-AQ LE
for Integration in systems with central control units
sensor for motion, light, temperature, relative humidity, air pressure and air quality

DALI-2 CS Corridor Integration
Compact DALI-2 sensor module for Integration in systems with central control units
sensor for motion detection (PIR) & light intensity

Push Button Coupler, input 4 x 230V (10m), flexible configurable, sequencer, macros, DT8, DALI-2 Application Controller and Instances, DIN Rail, factory default setting: Application Controller activated (changeable DALI Cockpit), 4 Potentiometers to set t

DALI ROT is a rotary knob basis to control the light level of DALI luminaires. Versions for Tunable White or RGB-capable luminaires are also available. The device was developed to fit the rotary covers and knobs of most manufacturers and to enable their i

This interface converts DALI signals into a 1-10V control signal and allows the integration of operating devices with two 1-10V control inputs for brightness and color temperature into a DALI system. Output mode for channel1 / channel2 can be defined as e

This compact module converts analogue 0-10V control signals into DALI light levels. The module has an integrated bus supply for a small DALI system with up to 4 standard DALI ballasts (10mA). The device offers both a current sink and current source 0-10V

DALI SC / SC-A is a control unit to recall DALI scenes. The dial on the back of the device can be used to define which of the 16 scenes will be called at button push. A different light scene can be assigned to each of the 4 independent switch inputs. The

DALI Sequencer is a control unit to recall automatically timed instruction sequences. 4 different customised sequences can be programmed. Only one sequence can be active at a time, and is started and stopped by standard DALI commands. Housing variants fo

Cover and rotary knob

Module with serial interface to communicate with the DALI bus via RS232. Allows e.g. the connection of a PLC to a DALI system via RS232 for bidirectional data transmission. Suitable for addressing, configuration, status queries and monitoring. Housing var

Module with serial interface to communicate with the DALI bus via RS232. Allows e.g. the connection of a PLC to a DALI system via RS232 for bidirectional data transmission. Suitable for addressing, configuration, status queries and monitoring. Housing var

With the DALI Expander 3, three new DALI sub-lines can be created and supplied with power and information. The connected devices within each DALI sub-line can be controlled broadcast, each sub-line via its own DALI address. Alternatively the DALI sub-line

With the DALI Expander a new DALI sub-line can be created and supplied with power and information. The connected devices within the DALI sub-line can be controlled broadcast via the address of the DALI Expander. Alternatively the DALI sub-line can be cont

DALI-2 ROT Touch
L4: RGB and scenes

DALI ROT is a rotary knob basis to control the light level of DALI luminaires. Versions for Tunable White or RGB-capable luminaires are also available. The device was developed to fit the rotary covers and knobs of most manufacturers and to enable their i

DALI LED-driver (CC) with 2 channels to control Tunable White luminaires via one DALI address (DT8). As alternative to the DT8 control the device also supports the operating modes Balance&Dim, Dim2Warm and SwitchDim2 (control via 2 switch inputs without D

DALI LED-driver (CC) with 4 independent channels. Each channel has its own DALI address. As alternative to the DT6 control the device also supports the operating modes Colour&Dim (suitable for RGB and RGBW luminaires) and SwitchDim2 (control via 2 switch

This interface converts DALI signals to a 1-10V control signal, thus enables the integration of operating devices with 1-10V control input into a DALI system. With the help of the switching relay the power supply of operating devices can be switched on an

DALI interface module to convert DT8-Tc control commands to DT6 control signals. The module enables dimming and the setting of the colour temperature via DT8 commands, also for luminaires with two DALI DT6 LED-driver.

This compact module converts analogue 0-10V control signals into DALI light levels. The module has an integrated bus supply for a small DALI system with up to 10 standard DALI ballasts (30mA). The device offers both a current sink and current source 0-10V

This compact module converts analogue 0-10V control signals into DALI light levels. The module has an integrated bus supply for a small DALI system with up to 4 standard DALI ballasts (10mA). The device offers both a current sink and current source 0-10V

DALI GC / GC-A is a control unit to address 2 DALI groups. With this compact module conventional light switches or pushbuttons can be used to send dimming and switching commands to 2 DALI groups. Using the dial on the back of the device the DALI/ luminari