Collection

Module with serial interface to communicate with the DALI bus via RS232. Allows e.g. the connection of a PLC to a DALI system via RS232 for bidirectional data transmission. Suitable for addressing, configuration, status queries and monitoring. Housing var

DALI-2 CS Integration THP-AQ LE
for Integration in systems with central control units
sensor for motion, light, temperature, relative humidity, air pressure and air quality

Compact sensor module with motion detection (PIR) and light intensity measurement for DALI-2 systems. The module gathers measurements for the building management system (instance mode) – (DALI-2 CS Master, WAGO, Beckhoff, etc.).

DALI LED-driver (CC) with 4 independent channels. Each channel has its own DALI address. As alternative to the DT6 control the device also supports the operating modes Colour&Dim (suitable for RGB and RGBW luminaires) and SwitchDim2 (control via 2 switch

DALI LED-driver for Tunable White LED. Input voltage 230VAC, output with secure isolation between mains and DALI, independent control of light level and colour temperature (DT8). As alternative to the DT8 control the device also supports the operating mod

This interface converts DALI signals into a 1-10V control signal and allows the integration of operating devices with two 1-10V control inputs for brightness and color temperature into a DALI system. Output mode for channel1 / channel2 can be defined as e

This interface converts DALI signals to a 1-10V control signal, thus enables the integration of operating devices with 1-10V control input into a DALI system. With the help of the switching relay the power supply of operating devices can be switched on an

This interface converts DALI signals to a 1-10V control signal, thus enables the integration of operating devices with 1-10V control input into a DALI system. With the help of the switching relay the power supply of operating devices can be switched on an

This compact module converts analogue 0-10V control signals into DALI light levels. The module has an integrated bus supply for a small DALI system with up to 4 standard DALI ballasts (10mA). The device offers both a current sink and current source 0-10V

DALI GC / GC-A is a control unit to address 2 DALI groups. With this compact module conventional light switches or pushbuttons can be used to send dimming and switching commands to 2 DALI groups. Using the dial on the back of the device the DALI/ luminari

The DALI CDC enables a day time based adjustment of colour temperature and light level for Tunable White capable DALI DT8 luminaires (circadian daylight curve). The curve can be adjusted to fit the respective application.

Module with serial interface to communicate with the DALI bus via RS232. Allows e.g. the connection of a PLC to a DALI system via RS232 for bidirectional data transmission. Suitable for addressing, configuration, status queries and monitoring. Housing var

With the DALI Expander a new DALI sub-line can be created and supplied with power and information. The connected devices within the DALI sub-line can be controlled broadcast via the address of the DALI Expander. Alternatively the DALI sub-line can be cont

DALI ROT is a rotary knob basis to control the light level of DALI luminaires. Versions for Tunable White or RGB-capable luminaires are also available. The device was developed to fit the rotary covers and knobs of most manufacturers and to enable their i

DALI ROT is a rotary knob basis to control the light level of DALI luminaires. Versions for Tunable White or RGB-capable luminaires are also available. The device was developed to fit the rotary covers and knobs of most manufacturers and to enable their i

DALI LED-driver (CC) with 2 channels to control Tunable White luminaires via one DALI address (DT8). As alternative to the DT8 control the device also supports the operating modes Balance&Dim, Dim2Warm and SwitchDim2 (control via 2 switch inputs without D

This compact module converts analogue 0-10V control signals into DALI light levels. The module has an integrated bus supply for a small DALI system with up to 4 standard DALI ballasts (10mA). The device offers both a current sink and current source 0-10V

DALI SC / SC-A is a control unit to recall DALI scenes. The dial on the back of the device can be used to define which of the 16 scenes will be called at button push. A different light scene can be assigned to each of the 4 independent switch inputs. The

DALI Sequencer is a control unit to recall automatically timed instruction sequences. 4 different customised sequences can be programmed. Only one sequence can be active at a time, and is started and stopped by standard DALI commands. Housing variants fo

DALI Sequencer is a control unit to recall automatically timed instruction sequences. 4 different customised sequences can be programmed. Only one sequence can be active at a time, and is started and stopped by standard DALI commands. Housing variants fo

Cover and rotary knob

With the DALI Expander 3, three new DALI sub-lines can be created and supplied with power and information. The connected devices within each DALI sub-line can be controlled broadcast, each sub-line via its own DALI address. Alternatively the DALI sub-line

DALI-2 ROT Touch
L4: RGB and scenes

DALI-2 ROT Touch
L2: groups, scenes and blinds