Collection

integration of up to 4 EnOcean buttons, configurable, sequencer, macros, DT8, DALI-2 application controller and instances, delivery status: application controller active, instances deactivated

Device with 2 DALI Tunable White LED dimmers. Suitable for constant voltage (CV) LED modules of 12V to 48V.

2 DALI addresses (Device Type 8, Color Type Tc), each DT8-Tc address allows independent control of brightness and color temperature.
Available

DALI LED-driver (CC) with 4 independent channels. Each channel has its own DALI address. As alternative to the DT6 control the device also supports the operating modes Colour&Dim (suitable for RGB and RGBW luminaires) and SwitchDim2 (control via 2 switch

DALI RM8/RM16 provides a via DALI bus controllable relay switch, which allows direct switching of permanent loads up to 2kW. Various compact designs and variations with make contact or changeover contact are available. The purposeful switching in voltage

This interface converts DALI signals to a 1-10V control signal, thus enables the integration of operating devices with 1-10V control input into a DALI system. With the help of the switching relay the power supply of operating devices can be switched on an

This interface converts DALI signals to a 1-10V control signal, thus enables the integration of operating devices with 1-10V control input into a DALI system. With the help of the switching relay the power supply of operating devices can be switched on an

This compact module converts analogue 0-10V control signals into DALI light levels. The module has an integrated bus supply for a small DALI system with up to 4 standard DALI ballasts (10mA). The device offers both a current sink and current source 0-10V

DALI GC / GC-A is a control unit to address 2 DALI groups. With this compact module conventional light switches or pushbuttons can be used to send dimming and switching commands to 2 DALI groups. Using the dial on the back of the device the DALI/ luminari

Compact control module for automatic power reduction / brightness reduction for night-time. The device has an integrated bus supply (20mA) for up to 7 standard DALI loads, extension possible to max. 64 loads is possible with a DALI Expander.

2 operatin

The DALI CDC enables a day time based adjustment of colour temperature and light level for Tunable White capable DALI DT8 luminaires (circadian daylight curve). The curve can be adjusted to fit the respective application.

DALI-2 CS Integration THP-AQ
for Integration in systems with central control units
sensor for motion, light, temperature, relative humidity, air pressure and air quality

Compact sensor module with motion detection (PIR) and light intensity measurement for DALI-2 systems. The module gathers measurements for the building management system (instance mode) – (DALI-2 CS Master, WAGO, Beckhoff, etc.).

DALI LED-driver (CC) with 2 channels to control Tunable White luminaires via one DALI address (DT8). As alternative to the DT8 control the device also supports the operating modes Balance&Dim, Dim2Warm and SwitchDim2 (control via 2 switch inputs without D

DALI LED-driver (CC) with 3 independent channels. Each channel has its own DALI address. As alternative to the DT6 control the device also supports the operating modes Colour&Dim (suitable for RGB luminaires) and SwitchDim2 (control via 2 switch inputs wi

DALI LED-driver for the constant current LED modules (CC) with 1 channel. Output signal can be controlled via DALI or SwitchDim2. Available with input voltage of 12V to 48V DC, different output currents ranging from 350mA to 2800mA, and PWM output.

Compact DALI motion sensor with integrated light sensor. The module can be used as a control unit for a DALI system or integrated in a building management system as simple sensor unit. The module is suitable for various applications such as offices, class

This interface converts DALI signals into a 1-10V control signal and allows the integration of operating devices with two 1-10V control inputs for brightness and color temperature into a DALI system. Output mode for channel1 / channel2 can be defined as e

This compact module converts analogue 0-10V control signals into DALI light levels. The module has an integrated bus supply for a small DALI system with up to 4 standard DALI ballasts (10mA). The device offers both a current sink and current source 0-10V

Module with serial interface to communicate with the DALI bus via RS232. Allows e.g. the connection of a PLC to a DALI system via RS232 for bidirectional data transmission. Suitable for addressing, configuration, status queries and monitoring. Housing var

Module with serial interface to communicate with the DALI bus via RS232. Allows e.g. the connection of a PLC to a DALI system via RS232 for bidirectional data transmission. Suitable for addressing, configuration, status queries and monitoring. Housing var

With the DALI Expander 3, three new DALI sub-lines can be created and supplied with power and information. The connected devices within each DALI sub-line can be controlled broadcast, each sub-line via its own DALI address. Alternatively the DALI sub-line

With the DALI Expander a new DALI sub-line can be created and supplied with power and information. The connected devices within the DALI sub-line can be controlled broadcast via the address of the DALI Expander. Alternatively the DALI sub-line can be cont

DALI-2 CS Integration THP-AQ LE
for Integration in systems with central control units
sensor for motion, light, temperature, relative humidity, air pressure and air quality

DALI ROT is a rotary knob basis to control the light level of DALI luminaires. Versions for Tunable White or RGB-capable luminaires are also available. The device was developed to fit the rotary covers and knobs of most manufacturers and to enable their i

DALI ROT is a rotary knob basis to control the light level of DALI luminaires. Versions for Tunable White or RGB-capable luminaires are also available. The device was developed to fit the rotary covers and knobs of most manufacturers and to enable their i

DALI ROT is a rotary knob basis to control the light level of DALI luminaires. Versions for Tunable White or RGB-capable luminaires are also available. The device was developed to fit the rotary covers and knobs of most manufacturers and to enable their i

DALI ROT is a rotary knob basis to control the light level of DALI luminaires. Versions for Tunable White or RGB-capable luminaires are also available. The device was developed to fit the rotary covers and knobs of most manufacturers and to enable their i

DALI LED-driver (CC) with 2 independent channels. Each channel has its own DALI address. As alternative to the DT6 control the device also supports the operating modes Balance&Dim, Dim2Warm (suitable for Tunable White luminaires) and SwitchDim2 (control v

A compact DALI motion detector with integrated light and temperature sensor. The module can be used as a control unit for a DALI system or as a measurement tool in combination with central control unit. The module is suitable for various applications such

LED driver (CV) with one channel, can be operated as PWMBooster or Dimmer. The device operates as PWM-Booster, if PWM-signals are applied to the input (50Hz-1kHz). If operated with 100kΩ potentiometer or 0-10V control devices (active and passive), the dev

This interface converts DALI signals to a galvanically isolated PWM signal, thus enables the integration of operating devices with PWM control input into a DALI system. DALI Device Type 5 (IEC62386-206) compatible: linear or logarithmic dimming curve, swi

This compact module converts analogue 0-10V control signals into DALI light levels. The module has an integrated bus supply for a small DALI system with up to 4 standard DALI ballasts (10mA). The device offers both a current sink and current source 0-10V

The DALI CDC enables a day time based adjustment of colour temperature and light level for Tunable White capable DALI DT8 luminaires (circadian daylight curve). The curve can be adjusted to fit the respective application.

DALI Sequencer is a control unit to recall automatically timed instruction sequences. 4 different customised sequences can be programmed. Only one sequence can be active at a time, and is started and stopped by standard DALI commands. Housing variants fo

cross plate

DALI-2 ROT Touch
L4: RGB and scenes