Interface with 4, from the DALI bus galvanically isolated, inputs for mains voltage. The inputs can be individually configured with target address, button behaviour and DALI commands. Beside the standard functions, dimming, switching, scene recall, etc.,

Interface with a, from the DALI bus galvanically isolated, input for mains voltage. The input can be configured with target address, button behaviour and DALI commands. Beside the standard functions, dimming, switching, scene recall, etc., predefined macr

The DALI USB is used as interface between the DALI Cockpit PC Software and the devices on the DALI bus. It enables the addressing and configuration of DALI installations. The DALI USB is available in 6 different versions: with strain relief, for DIN Rail

DALI Jalousie module can be used to control blind motors with 230V control input via DALI. Four configurable profiles can be programmed to open/close the blinds and to change the tilt angle. Different versions suitable for DIN rail mounting or remote ceil

This interface converts DALI signals to a 1-10V control signal, thus enables the integration of operating devices with 1-10V control input into a DALI system. With the help of the switching relay the power supply of operating devices can be switched on an

DALI-2 CS Mini Integration
Compact DALI-2 sensor module for Integration in systems with central control units
sensor for motion detection (PIR) & light intensity

Multifunctional DALI-2 control and operating unit for DALI emergency light systems, addressing and set-up of the DALI emergency light system, monitoring and management, white

The DALI-2 Display 7″ Emergency is a multifunctional control and operating un

Compact sensor module with motion detection (PIR) and light intensity measurement for DALI and DALI-2 systems. The module can either be used to directly control the DALI system (application controller) or simply to gather measurements for a building manag

DALI LED-driver (CV) with 3 independent channels. Each channel has its own DALI address. As alternative to the DT6 control the device also supports the operating modes Colour&Dim (suitable for RGB luminaires) and SwitchDim2 (control via 2 switch inputs wi

DALI relay controller with 4 channels. Each channel has its own DALI address. Designed for controlling relays and contactors with 12V to 48V DC control input. Different versions suitable for DIN rail mounting or remote ceiling installation (housing with s

The DALI-2 RM16 HS WE is a relay with DALI control for switching loads up to 2kW. Features zero-cross switching and DIN-rail mounting. Art. No.: 86456203-HS-WE.

This interface converts DALI signals to a 1-10V control signal, thus enables the integration of operating devices with 1-10V control input into a DALI system. With the help of the switching relay the power supply of operating devices can be switched on an

With only one DT6 DALI address, the Dim2Warm module allows the simultaneous control of brightness while changing the colour temperature. The lower the dimming value, the warmer the light.

DALI GC / GC-A is a control unit to address 2 DALI groups. With this compact module conventional light switches or pushbuttons can be used to send dimming and switching commands to 2 DALI groups. Using the dial on the back of the device the DALI/ luminari

DALI-2 CS Integration THP LE
for Integration in systems with central control units
sensor for motion, light, temperature, relative humidity & air pressure

DALI-2 CS Corridor Integration
Compact DALI-2 sensor module for Integration in systems with central control units
sensor for motion detection (PIR) & light intensity

DALI-2 CS Corridor
Compact sensor module with integrated motion detection (PIR), light intensity measurement and light control unit.
Due to the horizontal detection angle (150 °), the sensor is particularly suitable for wall mounting, e.g. in corridors.

Interface with 4, from the DALI bus galvanically isolated, inputs for mains voltage. The inputs can be individually configured with target address, button behaviour and DALI commands. Beside the standard functions, dimming, switching, scene recall, etc.,

DALI PS serves as power supply for the DALI bus system. Standardised voltage and current limitation as well as timing ensure a reliable bus communication. With the output current of up to 250mA and entire DALI line can be supplied. Up to 64 addressable DA

DALI-2 ROT Integration
DALI-2 ROT Integration is a rotary and push button for integration into higher-level building management systems (WAGO, Beckhoff, LUNATONE DALI-2 KNX gateway).

24V DC, 130mA Power Supply

Power supply 24V, 130mA, back box

increase the number of DALI lines for the DALI-2 Display 7”, 3 additional DALI lines, use in combination with a DALI-2 Display 7”


DALI-2 Display Bus Extension
The module is used in combination with a DALI-2 Display 7” Plus or DALI-2 Display 7” Emerg

DALI LED-driver (CC) with 3 independent channels. Each channel has its own DALI address. As alternative to the DT6 control the device also supports the operating modes Colour&Dim (suitable for RGB luminaires) and SwitchDim2 (control via 2 switch inputs wi

DALI RM8/RM16 provides a via DALI bus controllable relay switch, which allows direct switching of permanent loads up to 2kW. Various compact designs and variations with make contact or changeover contact are available. The purposeful switching in voltage

A compact DALI motion detector with integrated light and temperature sensor. The module can be used as a control unit for a DALI system or as a measurement tool in combination with central control unit. The module is suitable for various applications such

This compact module converts analogue 0-10V control signals into DALI light levels. The module has an integrated bus supply for a small DALI system with up to 4 standard DALI ballasts (10mA). The device offers both a current sink and current source 0-10V

Compact sensor module with motion detection (PIR) and light intensity measurement for DALI-2 systems. The module gathers measurements for the building management system (instance mode) – (DALI-2 CS Master, WAGO, Beckhoff, etc.).

DALI ROT is a rotary knob basis to control the light level of DALI luminaires. Versions for Tunable White or RGB-capable luminaires are also available. The device was developed to fit the rotary covers and knobs of most manufacturers and to enable their i

DALI LED-driver (CV) with 4 independent channels. Each channel has its own DALI address. As alternative to the DT6 control the device also supports the operating modes Colour&Dim (suitable for RGB and RGBW luminaires) and SwitchDim2 (control via 2 switch

DALI LED-driver for the constant current LED modules (CC) with 1 channel. Output signal can be controlled via DALI or SwitchDim2. Available with input voltage of 12V to 48V DC, different output currents ranging from 350mA to 2800mA, and PWM output.

DALI LED-driver for Tunable White LED. Input voltage 230VAC, output with secure isolation between mains and DALI, independent control of light level and colour temperature (DT8). As alternative to the DT8 control the device also supports the operating mod

DALI Jalousie module can be used to control blind motors with 230V control input via DALI. Four configurable profiles can be programmed to open/close the blinds and to change the tilt angle. Different versions suitable for DIN rail mounting or remote ceil

Compact DALI motion sensor with integrated light sensor. The module can be used as a control unit for a DALI system or integrated in a building management system as simple sensor unit. The module is suitable for various applications such as offices, class

This interface converts DALI signals to a 1-10V control signal, thus enables the integration of operating devices with 1-10V control input into a DALI system. With the help of the switching relay the power supply of operating devices can be switched on an

This compact module converts analogue 0-10V control signals into DALI light levels. The module has an integrated bus supply for a small DALI system with up to 10 standard DALI ballasts (30mA). The device offers both a current sink and current source 0-10V

This compact module converts analogue 0-10V control signals into DALI light levels. The module has an integrated bus supply for a small DALI system with up to 4 standard DALI ballasts (10mA). The device offers both a current sink and current source 0-10V